Tag Archives: Camera

Volkswagen A Pillar Bullet Camera Mount suits Golf, Jetta, Passat and Rabbit

a_pillar_finishedMounting a bullet camera in the Volkswagen Golf without using suction mounts on the window or screwing into the trim is quite difficult especially around the rear vision mirror as the RegenLichtSens (RainLightSensor) means the camera needs to be mounted forward close to the glass. There are two places where cameras can be attached with damaging trim, one is to the A pillar by removing the AirBag insert and the other is to the rear vision mirror which will be covered shortly.

Remove the AirBag insert by levering it from the lower long edge, this insert is generally not reusable as the clips bend and placing it back in there leaves it a little loose. You can use this again to cover the mount that has been fabricated. New inserts from VW are around AUD$1.35 (Anthracite part number 1K0853437B71N).

a_pillar_step_1

The insert on the left is the original one, you can see the marks on the bottom edge where it has been levered out. The four tabs on the bottom bend outwards slightly when removed and they can’t be bent back in all the way so after the first removal they feel slightly loose and after a few removals a tab will proably snap off. The insert on the right is a brand new one, they snap into place by putting the two tabs at the rear (in the photo – the tabs are at the top when you put them back into the car) into the the trim and then pushing down the at the bottom to snap the trim in.

a_pillar_inserts

Now that the AirBag insert has been removed you will see a screw (Torx T-20 to remove) that needs to be removed, take care or it will fall inside the A pillar trim. This screw isn’t used again so set it aside.

a_pillar_step_2

Next the bracket needs to fabricated, you need to obtain a bike light that looks similar to this one. You can purchase this from DealExtreme for USD$2.59 delivered worldwide.

a_pillar_bike_light

Modify the bracket as per the photo, this is designed for the right hand side of the car, the left hand side needs to be the mirror image. The bracket fits just above where the screw goes which passes through the slot in the bracket. The screw holds this in place firmly inside, you can adjust the angle of the bracket by adjusting the angle of the plastic above the slot.

a_pillar_bracket_1 a_pillar_bracket_2

The screw that was in the bracket is too short to pass through the plastic so replace it with a 8g 25mm self drilling metal screw as shown. Place the bracket in the hole and move it into position and place the screw in, you can adjust the bracket a little at this stage and tighten up. Just before the final turn hold the A pillar and push it into the correct position, don’t tighten too tight or you break the bracket.

a_pillar_bracket_3

The next step is to cut the existing AirBag insert to fit the space around the bracket, you will have to remove some or all of the tabs to do this (not shown). Then mount the round part of the bracket which is designed for a bike tube, most bullet cameras with a diameter of around 21mm and above will fit without having to add extra packing. That’s the job completed. The wiring for the bullet cam can be run either down inside the A pillar which requires it to be removed or if the cable is a thin one you can pull back the rubber seal and run it down inside that.

a_pillar_finished1

Volkswagen Golf Reverse Camera Upgrade RNS510

Update: Installing a Golf Mark VI Rear View Camera (RVC) into a Golf Mark V

The Golf can have the factory reverse system from other models (generally Tiguan 5N0) installed, there are a few caveats that must be checked first as some components in the car must be a particular revision or higher.

Gateway needs to be 3C0 907 530 H or higher. For the Tiguan or Passat controller you need to use a 9-byte long CAN gateway (L or N at the end), the Touareg controller may only require a 8 byte controller.

Kufatec sell a harness that connects the RNS510 to the reverse camera controller for 89 euros.

Parts required for install (not using the hatch/boot release detailed below)

Reverse Controller Tiguan- 5N0907441
Reverse Controller Toureg – 7L6907441B (not recommended)
Reverse Controller Holder – 5N0909537A
Camera – 5N0980551A
Cable for Camera 3M – 000098654A

Using VCDS/Vagcom you need to code the CAN gateway (19), the RNS510 (37 or 56), the RVC controller with 0010007 and then perform a camera calibration.

Camera mounting option – rear hatch/boot release

Integrating the camera into the rear pop up hatch release has been a project I’ve been looking into for a while, this is now made easier by the release of the MK6 Golf as this has a camera integrated into the hatch release.

Part Numbers

Golf 6 hatch release – 5K0 827 469J
Passat CC boot release – 5K0 827 469H

Mounting gasket is the same for Golf 6, Passat CC and Golf 5. Switch for the hatch/boot release is the same as well.

Both Golf 5 and Golf 6 use the Q CANBUS gateway.

Using an aftermarket reverse camera with the RNS510

I’m currently working on this as part of another project so the information here is sketchy for the time being.

In the Radio Configuration II there is a Byte 3, Bit 6 (Backup Camera Low – without control module)

RNS2 and RNS510 Connector Differences
RNS2 and RNS510 Connector Differences