This guide covers the installation of the puddle lights to the Volkswagen Golf and Jetta front doors as fitted in some countries and specifications of Mark V’s and to some models of the EOS. Along with the Door Warning Lights these really light up the area around the side of the car.
The light operates every time the door is operated and stays on after you close the door (longer than the coming home time) but turn off when you arm/lock the car. When you unlock the car they turn on and stay on longer than the leaving home time.
Adding puddle lights to the Volkswagen Golf or Jetta can be be achieved in two ways.
- Purchase new mirrors with puddle lights fitted (estimated cost AUD$800/USD$400)
- 1K1 857 507 BT 9B9 – Driver’s Mirror, power, heated, puddle lights (MY06 Golf/Jetta)
- 1K1 857 508 BR 9B9 – Passenger’s Mirror, power, heated, puddle lights (MY06 Golf/Jetta)
- Modify the existing mirrors to add a lense and suitable leds (estimated cost AUD$30/USD$25)
- Trim Removal Tools
- Selection of heat shrink tubing (3-5mm), soldering iron/blowtorch, solder
- Vagcom/VCDS to code the door (this can be done before or after the install)
Volkswagen Golf & Jetta Door Controller Information Mark V has information on the door controllers. This guide was based on the install in my March 2008 build MY08 GTI.
First remove the door trim – Passengers Front Door Trim – Removal and Installation
The mirror cover – Removal and Installation of Mirror Covers from the Volkswagen Golf Mark V
And finally the mirror – Removal and Installation of Mirrors from the Volkswagen Golf Mark V
Extra cable to mirror
Adding extra cable to the mirror for the lights – this section can be skipped if you want to use the mirror heating cabling instead.
This is where the cable exits the mirror and enters inside the car.
This is the other end where the cable appears inside the mirror. Start by inserting the wire into the top and pushing inside.
The cable will be visible and you can fish it out with a suitable piece of wire.
Pull the wire through until you have almost enough to reach the controller. We need to wrap this cable next.
Using an exterior fabric adhesive tape – Fabric Adhesive Tape for wiring looms and harnesses – cover enough of the cable so that the part inside the mirror hinge and partway out each end is covered with two layers. This is especially important on the motorised mirrors that fold back.
Now pull the covered section through.
Leaving the uncovered section out like this.
Route the new cable as follows to follow the path of the existing cable.
And tape it to the existing loom.
This step identified Pin 10 as the positive power for the puddle light.
Insert the repair wire into the pin 10 position. Note. if you are using the mirror heater connection what you need to do is remove the pin from the mirror heater position and move it to pin 10.
Place a suitable piece of heat shrink tubing (3.5mm to 4.5mm) on the repair wire, bare the ends of the repair wire and new wire to the mirror and twist them together before soldering.
Now pull the heat shrink over the connection and apply heat to shrink.
Using an interior fabric adhesive tape – Fabric Adhesive Tape for wiring looms and harnesses – wrap the new cable onto the existing mirror loom.
Replace the Door Mirror
Now reinstall the door mirror – Removal and Installation of Mirrors from the Volkswagen Golf Mark
Fit the puddle light and lense to the mirror
Depress the clips on the rear of the mirror at the points shown and pull the frame towards you as shown by the arrows and it will slide off.
Undo the two torx screws shown to release the mirror indicator and the lower housing from the mirror (torx T10)
Once the indicator and housing are hanging depress the clip around the middle of the indicator and the two will separate.
Work out where you want the lense to be installed taking into account clearance at the front of the mirror for the mirror assembly, the frame we removed earlier and the height of the LED module.
Drill from the inside of the housing using a hole saw into some scrap timber (with paper towels on top if you don’t want to scratch the surface).
Next dremel around where the lense will go to increase the clearance for the LED module and to decrease the lip underneath the mirror housing.
Clean the surface with a suitable cleaner and apply some automotive silicone.
Push the glass into place and clean the excess off with mineral turpentine.
There will be a gap around the outside in which you fill with a 5 minute two part epoxy for strength. The silicone is mainly there for waterproofing plus the epoxy means after 30 minutes we can continue with the install. Remember to allow the silicone time to cure before you get it wet.
Fit the LED module into location and using 5 minute epoxy glue it into position, build the back up with double sided tape to provide mechanical strength.
The LED module glued into position.
Now reattach the indicator, route the wire (you will need to extend the stock wires, DON’T use the connector that came with it as they are useless and it will fail but instead solder the new ones and use heatshrink tubing) and check that the LED module is securely in place.
Removed the negative connection to the mirror and solder a wire to it and to the negative wire on the LED module before reattaching to the mirror. Use tape to connect the new wire to the mirror heater wire.
Note: If you are using the mirror heater wires for power detach the positive wire and solder a wire to it and the positive wire of the LED module but do not reattach the positive wire, instead pull it into the rear of the mirror and heatshrink it.
Both wires reattached to the mirror and the mirror surround frame slid back on.
Wrap the connectors up well to protect from water ingress.
Code the puddle light
Open the door controller, in this guide it’s the drivers door – 42 and select “Coding – 07”
Make a note of the coding value.
Add 2 to the coding value and select “Do It!” to save.
Select “Close Controller” to exit.
Replace the Door Mirror Cover
Reinstall the door mirror cover – Removal and Installation of Mirror Covers from the Volkswagen Golf Mark V
The finished product