MDI 0150 KW22-2011

MDI 0111 KW22-2010

MDI 0090 KW33-2009

General Notes (for all versions)

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file formats and connectivity.

Firmware is for units with a [...]]]> Firmware Changes

Version 0150 – production (from week) KW22/2011 (launched KW45/10)
(any MDI’s produced or fitted in the factory from week 22 2011 onwards should have this version fitted out of the factory)

General Notes

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file formats and connectivity.

Firmware is for units with a software version of 0090 or greater, if firmware is unable to be updated or you have already flashed this version it will not load.

• Download the firmware from one of the links below.
• Copy the file mdi.bin.enc in the root (top) level of a USB flash drive and insert this into the USB cable.
• Turn the headunit on or start the car and the update will proceed. If the MDI is selected the status will be displayed.
• After around 1 minute the update will complete and the USB flash drive may be removed.

VW MDI KW22/2011 Firmware (primary download site – this will have the latest if there are any updates so if you want a specific version use the link below)

VW MDI KW22/2011 Firmware

(This file needs to be renamed from mdi.bin.kw22-2011.enc to mdi.bin.enc. You may not see the .enc extension so this is nothing to worry about – just remove the version number “.kw22-2011″ and proceed with the update)

Possible Error Messages during the update process

• Update with older version is not possible
  • The file on the USB flash drive is older than the software version on the MDI.

• Update on the same version is not possible
  • The file on the USB flash drive is the same as the software version on the MDI.

• Update file is corrupted or damaged
  • Re download the file and start again

• Multiple update files found
  • There are multiple update files in the root of the USB flash drive, delete the older versions and start again.

• Update was terminated
  • An error has occured in the update, start again.

USB Memory Sticks and Hard Drives

Portable Music Players

Known Characteristics of Devices

Windows won’t allow you to create a FAT32 filesystem over 32GB but it can be performed using [...]]]> The Volkswagen Media Device Interface (MDI) requires external hard or flash drives to have a FAT16 filesystem for under 2GB sized media or a FAT32 filesystem for over 2GB media. See Volkswagen Media Device Interface (MDI) Specifications for the details.

Windows won’t allow you to create a FAT32 filesystem over 32GB but it can be performed using a tool like fat32format (they have a GUI and command line version) which will allow to format a drive up to 2TB.

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for the latest version.

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file [...]]]> Firmware Changes

Version 0111 – production (from week) KW22/2010
(any MDI’s produced or fitted in the factory from week 22 2010 onwards should have this version fitted out of the factory)

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for the latest version.

General Notes

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file formats and connectivity.

Firmware is for units with a software version of 0090 or greater, if firmware is unable to be updated or you have already flashed this version it will not load.

• Download the firmware from one of the links below.
• Copy the file mdi.bin.enc in the root (top) level of a USB flash drive and insert this into the USB cable.
• Turn the headunit on or start the car and the update will proceed. If the MDI is selected the status will be displayed.
• After around 1 minute the update will complete and the USB flash drive may be removed.

VW MDI KW22-2010 Firmware

(This file needs to be renamed from mdi.bin.kw22-2010.enc to mdi.bin.enc. You may not see the .enc extension so this is nothing to worry about – just remove the version number “.kw22-2010″ and proceed with the update)

Possible Error Messages during the update process

• Update with older version is not possible
  • The file on the USB flash drive is older than the software version on the MDI.

• Update on the same version is not possible
  • The file on the USB flash drive is the same as the software version on the MDI.

• Update file is corrupted or damaged
  • Re download the file and start again

• Multiple update files found
  • There are multiple update files in the root of the USB flash drive, delete the older versions and start again.

• Update was terminated
  • An error has occured in the update, start again.

USB Memory Sticks and Hard Drives

Portable Music Players

Known Characteristics of Devices

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for the latest version.

General Notes

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file [...]]]> Firmware Changes

Version 0090 – production (from week) KW33/2009
(any MDI’s produced or fitted in the factory from week 33 2009 onwards should have this version fitted out of the factory)

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for the latest version.

General Notes

See Volkswagen Media Device Interface (MDI) Firmware Upgrades for general information on the firmware updates including restrictions, file formats and connectivity.

Firmware is for units with a software version of 0090 or greater, if firmware is unable to be updated or you have already flashed this version it will not load.

• Download the firmware from one of the links below.
• Copy the file mdi.bin.enc in the root (top) level of a USB flash drive and insert this into the USB cable.
• Turn the headunit on or start the car and the update will proceed. If the MDI is selected the status will be displayed.
• After around 1 minute the update will complete and the USB flash drive may be removed.

VW MDI KW33-2009 Firmware

(This file needs to be renamed from mdi.bin.kw33-2009.enc to mdi.bin.enc. You may not see the .enc extension so this is nothing to worry about – just remove the version number “.kw33-2009″ and proceed with the update)

Possible Error Messages during the update process

• Update with older version is not possible
  • The file on the USB flash drive is older than the software version on the MDI.

• Update on the same version is not possible
  • The file on the USB flash drive is the same as the software version on the MDI.

• Update file is corrupted or damaged
  • Re download the file and start again

• Multiple update files found
  • There are multiple update files in the root of the USB flash drive, delete the older versions and start again.

• Update was terminated
  • An error has occured in the update, start again.

The way this works is [...]]]> Whilst this guide is intended for the Volkswagen Skoda Bluetooth kit harness it applies to anything that requires interfacing to the quad lock connector on the rear of the head unit or that uses similar connectors around the car. This guide specifically for 2 x power connections and 2 x data connections.

The way this works is you remove the terminal from the housing, join that terminal to the matching terminal and insert the opposite terminal into the housing.

First you need to obtain the connector housings and repair wires.

• 1 x 000 979 133 (000979133) – 1mm repair wire – CAN bus Hi and Lo female.
• 1 x 000 979 134 (000979134) – 1mm repair wire – CAN bus Hi and Lo male.
• 1 x 000 979 225 (000979225) – 2.5mm repair wire – 12v and ground female.
• 1 x 000 979 226 (000979226) – 2.5mm repair wire – 12v and ground male.
• 4 x 191 972 701 (191972701) – Housing
• 4 x 191 972 711 (191972711) – Connector Housing

Step 1 – Cut the four repair wires in half, remove the insulation from the ends of all four and twist the exposed wire together. Do the same for the power and CAN bus wire. Join one male and one female repair wire half together (ensure that you join the 2.5mm female to the 2.5mm male) as shown and connect the ground wire to one and redo the step for the power wire.

Step 2 – Solder each of the four repair wire halves and the two power wires from the harness as shown.

Step 3 – Double the harness wire back on top of itself.

Step 4 – Using heat shrink cover each soldered area as shown. Use a smaller length to cover the join and than place a longer length over the top to minimise the chances of any shorts.

Step 5 – Repeat the last part of Step 1 with the 1mm repair wire and the CAN bus cable.

Step 6 – Place a piece of coloured heatshrink on one male/female CAN bus set, ensure that these are connected to the same wire! This allows you to ensure that you have hooked this up correctly later on. Repeat for the power set of cables.

Step 7 – This should be the finished result. Next tape it up using fabric adhesive tape – Fabric Adhesive Tape for wiring looms and harnesses

Step 8 – Install the housings and connector housings on the exposed terminals.

Step 9 – This is the finished harness ready for install.

Product Multimedia socket MEDIA-IN  

Stand: 06.03.2008 

Introduction 

About Multimedia socket MEDIA-IN audio files can be an “external Medium “on the radio-navigation system reproduced and controlled will. As the “external data” are USB Mass Storage and MP3 Player refers to the multimedia jack can be connected and on which Audio files are stored. 

Since the correctness [...]]]> (this has been translated roughly from a German Volkswagen document)

Product Multimedia socket MEDIA-IN  

Stand: 06.03.2008 

Introduction 

About Multimedia socket MEDIA-IN audio files can be an “external Medium “on the radio-navigation system reproduced and controlled will. As the “external data” are USB Mass Storage and MP3 Player refers to the multimedia jack can be connected and on which Audio files are stored. 

Since the correctness of the software in mobile audio players by Volkswagen not be and the software versions of the device manufacturer can also change, are Functional impairments in the vehicle possible. These are not at Volkswagen responsible. 

Therefore, selected audio devices and software versions continuously on their compatibility with Multimedia socket checked.

Boundary 

• Only external disk or USB mass storage  (Mass Storage Device) which supports USB 2.0 specified. 

• An external disk, according to the FAT filesystem FAT16 (<2GB) or FAT32 (> 2GB) structure (FAT: File Allocation Table). 

• In the case of complex file structures on the external disk (many files in a directory, many folders and subfolders, files, unplayable, etc.) there may be delays in the readout of the audio files. The Response time can be additionally affected by the connected device will. 

• The folder structure on the external disk to a depth of eight Folder levels do not exceed. A folder should be no more than 1000 entries included. 

• To connect an external USB disk must be no extension or USB hubs (USB distributor) may be used. 

• When an external disk into multiple partitions, only the first Partition with playable audio files is played. 

• Memory card adapters are not supported and may cause malfunction lead. 

• Has the software on an external MP3 player through the manufacturer updated (firmware upgrade), it can lead to malfunction during the Farm.

• An attached external disk may only be switched or there must be a corresponding data mode can be selected. 

• To operate the external disk read the manual of the respective manufacturer. 

• Supported file formats: You can audio files in MP3, WMA, OGG Vorbis, AAC format and an external disk on the radio device 

and controlled. 

• WMA audio files (Windows Media Audio) can only have the device be played if they do not have the DRM procedure (Digital Rights Management) are copyrighted. 

• Play in the formats PLS, B4S, ASX, and WPL will also be supported. 

• The play list information stored in a certain set playback order saved MP3 files. There are no playlists in MP3 Files. A playlist can only be played when the title to which the play refers to the same place on the data stored are. Otherwise, the playlist can not be played.

 USB Sticks

Music/Video Player

At the Media-in devices should be protected against mechanical impact and other damage sources are protected. Any damage to the  connected devices can be no liability.

Known properties of devices

Volkswagen Accessories GmbH presents the contents of this statement with great care and ensures that they regular updating. Nevertheless, this data is only as information and can not replace detailed individual advice. The technical characteristics and equipment of products described are only examples. Such features and equipments can be particularly country-specific vary. Any changes are reserved. Authentic information about the technical Features, equipment or properties of our products are available exclusively from your currently Distributor or importer. Volkswagen Zubehör GmbH assumes no liability for the timeliness, Correctness and completeness of the information on these pages.

The Media Device Interface (MDI) offers support for USB devices (memory sticks and hard drives), iPod integration and Aux In along with displaying ID3 tags over the CANbus to the MFD and the RCD310, RCD510 and RNS510 headunit. The unit is available for the Passat which mounts in the glovebox and the Golf which mounts [...]]]>

MDI

The Media Device Interface (MDI) offers support for USB devices (memory sticks and hard drives), iPod integration and Aux In along with displaying ID3 tags over the CANbus to the MFD and the RCD310, RCD510 and RNS510 headunit. The unit is available for the Passat which mounts in the glovebox and the Golf which mounts in the centre console replacing the 6 stacker cd changer. It is possible to mount the unit elsewhere in the car.

UPDATE: Volkswagen have released a retrofit kit that comes without the additional trim for the cd changer mounting and is designed for mounting behind the dash. See here for further information.

• Module with USB cable for Golf/Passat/Jetta: Part Number 5N0 035 341 B (5N0035341 B)  - 1stvwparts.com USD$255.86
• Module with USB cable for Tiguan: Part number 5N0 035 341 (5N0035341) 1stvwparts.com USD$300.94)
  
• iPod cable: Part Number 000 051 446 C (000051446C)  - 1stvwparts.com ~USD$51
• AUX in cable: Part Number 000 051 446 D (000051446D)
• Extension cable for MDI interface 000 051 447 (000051447)

If you want to install the unit into the cd changer location on a GTI with Anthracite trim that doesn’t have a changer installed in the console between the seats you will need the following parts

• CD Changer Center Console: Part Number 1K0 863 323A 71N (1K0863323A71N)
• CD Changer Insert: Part Number 1K0 863 328A 71N (1K0863328A71N)
• CD Changer Air Duct: Part Number 1K0 864 255C (1K0864255C)

MDI installed in CD Changer Location

To remove the CD Changer housing to make the MDI easier to mount (Glovebox for example) remove the two T20 screws and then press down on the two clips on the unit to release it.

Pinouts on Media Device Interface (MDI), Bold connections only used if CD changer being retained.

Pin 1: Ground
Pin 2: CAN Low
Pin 3: not used
Pin 4: NFR+/AUX R+
Pin 5: NFL+/CD Changer pass thru
Pin 6: NFR+/CD Changer pass thru
Pin 7: 12V
Pin 8: CAN High
Pin 9: NFL+/AUX L+
Pin 10: NF-/AUX -
Pin 11: NF-/CD Changer pass thru
Pin 12: Shield for CD Changer pass thru cable

Make custom harness for connecting to headunit

• 2m of 2 conductor shielded wire
• 2m of unshielded twister pair
• 4m of 18 guage wire
• 5 x 000 979 009 repair wire
• 8E0 972 112 housing

Place two connectors on the UTP for CAN High and CAN Low, two connectors on the 18guage wire for 12V and Ground and two connectors to the 2 conductor shielded wire. This is the end for the MDI and for the end on the head unit side you can splice these wires or use a bluetooth or similar harness.

MDI Interface    Headunit

Pin 1 Ground – T16/12
Pin 2 CAN Low – T16/10
Pin 4 NFR+/AUX R+ – T12B/7
Pin 7 12V – T16/15
Pin 8 CAN High – T16/09
Pin 9 NFL+/AUX L+ – T12B/1
Pin 10 NF-/AUX- – T12B/2

Add Auxiliary input with MDI fitted.

• Aux in port: Part number 1K0 035 724B
• 3 wire connector housing: Part number 1C0 973 119B
• Terminals (2): Part number 000 979 009

Pin 1 of the 3 pin connector (R+) goes to Pin 4 of the MDI
Pin 2 of the 3 pin connector (-) goes to Pin 10 of the MDI
Pin 3 of the 3 pin connector (L+) goes to Pin 9 of the MDI

Kufatec sell this unit as a kit, click here for further information.

When using the USB with removable hard drive ensure that the drive is using a FAT32 file system, other types such as NTFS will not be usable.