There are a number of steps to programming your bluetooth after installation, you will need access to VAGCOM/VCDS to perform these steps although your local dealer may be able to do these by using his VAS5052 dealer tool but it will be more difficult then using VAGCOM/VCDS.
Step 1 – Program the CAN Gateway to allow the controller to use the gateway.
CAN Gateway – Controller 19
This controller uses Long Coding, recoding should be carried out using the Long Coding Helper built into VAG-COM. Select Byte 3 and put a tick in Bit 7 to enable Controller 77 Telephone. Write the Long Code back to the car.
Step 2 – Setup the telephone controller to function as per the settings chosen.
Telephone – Controller 77
The controller soft coding should be set to 0000422
0?xxxx: Motor Vechicle Type
0 – CANBUS
1 – D3/C6 High System
2 – C6 Standard System
0x?xxx: Steering Wheel Type
0 – non multifunction steering wheel
1 – standard steering wheel
2 – modular steering wheel
0xx?xx: Installed Components
1 – none
2 – Multi Function Steering Wheel
3 - Head Unit
4 - Multi Function Steering Wheel and Head Unit
5 – K-line
6 - Multi Function Steering Wheel and K-line
7 – Head Unit and K-line
8 - Multi Function Steering Wheel, Head Unit and K-line
0xxx?x: Language Spoken by Unit
0 – Language operation out
1 – German
2 – English (UK)
3 – French
4 – Italian
5 – Spanish
6 – Not Used
7 – English (US)
8 – Language operation of external equipment (RNS 510 etc)
9 – Speaker dependent language choice
0xxxx?: Language for MFD (Multi Function Display)
0 – no announcement in the MFD
1 – German
2 – English (UK)
3 – French
4 – Italian
5 – Spanish
6 – Not used
7 – English (US)
Now move onto channel adaption, the following channels should be adapted with the default values listed, information on these values is available further down the page.
channel 128 (base volume) - 0
channel 129 (disconnection delay)- 6
channel 130 (offset delay) – 2
channel 131 (mircrophone sensitivity) – 130
channel 132 (unknown) – 0
channel 133 (bluetooth on/off) – 1
channel 134 (speech on/off) – 0
channel 135 (bluetooth passkey)- 1234
channel 136 (offset delay) – 9
channel 137 (unknown) – 1
channel 139 (unknown) – 0
Channel 128 – Base volume (Base volume of the output)
000 – 0dB (no increase/decrease)
001 – +1dB increase
002 – +2dB increase
003 – +3dB increase
004 – +4dB increase
005 – +5dB increase
006 – +6dB increase
128 – -1dB decrease
129 – -2dB decrease
130 – -3dB decrease
131 – -4dB decrease
132 – -5dB decrease
133 – -6dB decrease
Channel 129 – Disconnection Delay (Disconnection delay after turning ignition off)
000 – 30 seconds
001 – 5 minutes
002 – 10 minutes
240 – 20 hours
Channel 130 – Offset Delay (Offset compenstion delay to avoid echoes)
0 – 0ms
1 – 1ms
2 – 2ms
….
11 – 11ms
12 – 12ms
Channel 131 – Microphone Sensitivity (Lower/Raise the Microphones Sensitivity)
000 – 0dB (no increase/decrease)
001 – +1dB increase
002 – +2dB increase
003 – +3dB increase
004 – +4dB increase
005 – +5dB increase
006 – +6dB increase
128 – -1dB decrease
129 – -2dB decrease
130 – -3dB decrease
131 – -4dB decrease
132 – -5dB decrease
133 – -6dB decrease
Channel 132 – unknown
0 – default
Channel 133 – Bluetooth (Bluetooth activate/deactivate)
0 – Disable
1 – Enable
Channel 134 – Speech Function (Speech control On-Off)
0 – On with fixed mobile phone and bluetooth
1 – Off with fixed mobile phone and not bluetooth
Channel 135 – Bluetooth Passkey (4 Digital Passkey to allow access to the bluetooth)
1234 – Default passkey
Channel 136 – Offset Delay (Offset compensation delay between transmit and receive)
001 – 0.1 seconds
002 – 0.2 seconds
003 – 0.3 seconds
004 – 0.4 seconds
…..
024 – 2.4 seconds
025 – 2.5 seconds
Channel 137 – unknown
1 – default
Channel 139 – unknown
0 – default
Step 3 – Multi Function Steering Wheel – Voice activation (optional)
If you car is fitted with the Multi Function Steering Wheel you can modify the mute button (* on the VW models) to activate the voice dialing feature. The phone button under this button is not usable at this time as this is designed to operate with the fixed car kit unit.
Controller 16 – Steering
Select Coding 07 and you should see a 7 digit softcode which will be in the format 00xxxxx
The 4th digit from the right corresponds to the steering wheel variant. If you have a 4 spoke Multi Function Steering Wheel without the Cruise Control buttons it should be a 2. Change this to a 3 and that should convert your Mute button to activate the Voice Dialling.
Software version 0101 or lower
0?xxxxx: Vehicle Type
- 0 = Normal
- 1 = Special Purpose (e.g Taxi)
0x?xxxx: Transmission
- 0 = Manual Transmission
- 1 = Automatic Transmission
0xx?xxx: Steering Wheel
- 0 = Steering Wheel without Multifunction
- 1 = 3-Spoke Steering Wheel without Multifunction
- 2 = 3/4-Spoke Steering Wheel with Multifunction without Cruise & Voice Control
- 3 = 3/4-Spoke Steering Wheel with Multifunction with Cruise & Voice Control
0xxx?xx: Additional Equipment
- +1 = Tiptronic (Shift Paddels)
0xxxx?x: Board Computer / Cruise Control System (CCS)
- 0 = w/o Board Computer and w/o Cruise Control System (CCS)
- 1 = with Board Computer and w/o Cruise Control System (CCS)
- 2 = w/o Board Computer and with Cruise Control System (CCS)
- 4 = with Board Computer and with Cruise Control System (CCS)
0xxxxx?: Rear Wiper
- 1 = Rear Wiper not installed
- 2 = Rear Wiper installed
Software version 0110 or higher
0?xxxxx: Driver-Assistance-Systems
- 0 = Driver-Assistance-Systems not installed
- 0 = Message for Driver-Assistance-Systems active w/o Button
- 1 = Message for Driver-Assistance-Systems inactive w/o Button
- 2 = Message for Driver-Assistance-Systems active with Button
- 3 = Message for Driver-Assistance-Systems inactive with Button
0x?xxxx: Vehicle Type
- 0 = Normal
- 1 = Special Purpose with Multi-Function Control Module (Steer. Column. Contr. Mod. as Master)
- 2 = Special Purpose with Multi-Function Control Module (Multi-Function Contr. Mod. as Master)
0xx?xxx: Transmission
- 0 = Manual Transmission
- 1 = Automatic Transmission
0xxx?xx: Multi-Function Steering Wheel
- 0 = Multi-Function Steering Wheel not installed
- 5 = Multi-Function Steering Wheel w/o Tiptronic and w/o Push-To-Talk (PTT) installed
- 6 = Multi-Function Steering Wheel with Tiptronic and no Push-To-Talk (PTT) installed
- 7 = Multi-Function Steering Wheel w/o Tiptronic and with Push-To-Talk (PTT) installed
- 8 = Multi-Function Steering Wheel with Tiptronic and with Push-To-Talk (PTT) installed
0xxxx?x: Cruise Control System (CCS) and Adaptive Cruise Control (ACC)
- 0 = Cruise Control System (CCS) not installed
- 1 = Cruise Control System (CCS) with 6 Positions via separate Stalk installed
- 2 = Adaptive Cruise Control (ACC) with 6 Positions via separate Stalk installed
- 3 = Cruise Control System (CCS) with 4 Positions via Blinker Stallk installed
- 4 = Cruise Control System (CCS) via Multi-Function Steering Wheel installed
- 5 = Adaptive Cruise Control (ACC) via Multi-Function Steering Wheel installed
0xxxxx?: Rear Wiper and Board Computer
- 1 = Rear Wiper not installed / Board Computer via Wiper Stalk not installed
- 2 = Rear Wiper installed / Board Computer via Wiper Stalk not installed
- 3 = Rear Wiper not installed / Board Computer via Wiper Stalk verbaut
- 4 = Rear Wiper installed / Board Computer via Wiper Stalk installed
Mate as always great info I just blindly coded according to stu but this is awesome.
Hello,
i have a problem; i have a new Golf VI GTi,i bought an original VW BT carkit (NOT the Premium) and installed it.
Everything works perfect with the RNS510, the only thing that don’t work is phone book browsing in FIS/MFA/MFD (do not know how you call the boardcomputer between the clock’s)
So everything is top, but i miss the option phonebook in my display…..
Can you help me, i do not know were to look…..
Greetings Ron
[...] gibt nur wenige Codierlisten zur Premium FSE Box, diese hier scheint recht plausibel: Zitat: von Link zur Webseite:Code:Telephone – Controller 77 [...]
Great write up on programming, just wonder are you able to do a write up programming using VAS5052 dealer tool as well?
Thanks, I haven’t got access to a dealer tool atm so can’t do that sorry.
Hi Maverick, i bought a Premium BT for my 2010 VW EOS (part # 3C8035730A )it came blank and needs coding, but the coding is a long one and didnt accept the 0000422. in general in binary coding helper window (in VCDS)there are 12 pairs of bits (24 digits), could you help me with this one,any one knows how to code the unit.
The controller soft coding should be set to 0000422, for a RNS 510 firm. 2660 with voice control, set to 0010402!
Maverick: do you now it is a coding to get the phone button not to mute, but get into the phone menu?? I can speak and use the telephone to call, but not use the touch screen to dial with. I hope you can answear me sooon. Cheers, Andy
Hi you guys,
just swapped the rsap module on my 2010 sciroco with part number 1Z0035729E a skids bluetooth unit. It was an easy hardware swap. The unit came pre programmed for Multi functinal steering wheel and White dot.
However, I had to take the car back to the dealers who typed in the code 0000422. This allowed me to pair my iPhone with the mfd display between the clocks BUT I cannot get the phone function or any recognition of the phone on the RNS510!!!
Does anyone know how to resolve this for me
cheers
By skids I meant Skoda. Sorry
Can anyone tell me if you can use this, or any coding to get a phone menu on a US spec RCD-510?
can somebody tell me good coding for 5NO 035 730 B ,vw passat 2009,multifunction steering well(8 butons),white dots, and RNS 510 2660. Now when I programed steriing well when I press * ,activate voice command but only from the telephone and microphone not work with bluetooth, working with voice command from rns(microphone is ok).
this page http://vwnavi.com/forums/showthread.php?p=50609 dont work…
please help
[...] dato un occhio qui?: Volkswagen / Skoda Bluetooth Programming | my-gti.com [...]
Hi Guys, i bought a Premium BT for my 2010 VW EOS (part # 3C8035730A )it came blank and needs coding, but the coding is a long one and didnt accept the 0000422. in general in binary coding helper window (in VCDS)there are 12 pairs of bits (24 digits), could you help me with this one,any one knows how to code the unit.
I have installed 7P6035730D bluetooth module in my skoda superb 2.0tdi with bolero system.
The work shop enabled the 77 telephone and my phone has started (VAG 912).
But when they scan for fault code we get malfunction in 77 telephone.
It even gives an error .ROD file not available.
The other problem is they typed a wrong WSC code as 00004 and now they
cannot make it 00000 as write enable option has gone after entering
the WSC code once.
How can I get rid of the fault code and make the wsc back to 00000.
Address 56: Radio
Protocol: CAN
Part No: 3T0 035 156 C
Component: BOLERO 013 0029
Coding: 0D0004000004
Shop #: WSC 33361
Address 77: Telephone
Protocol: CAN
Part No: 7P6 035 730 D
Component: TELEFON H05 0440
Coding: 0A00000000010100
Shop #: WSC 00004
ravjeet,
The WSC is irrelevant. Do not worry about that at all.
The “.ROD file not available” fault code probably exists, as it did in my “9W7″, because the scan tool doesn’t yet know what a 7P6035730D module is for. Don’t worry about it.
Rajeet,
One more thing…the code in your BT matches mine:
Address 77: Telephone (J412) Labels: None
Part No SW: 7P6 035 730 C HW: 7P6 035 730 C
Component: TELEFON H05 0440
Revision: 1B001001 Serial number: 00007667973792
Coding: 0A00000000010100
Shop #: WSC 02172 444 59389
ASAM Dataset: UHVNA A01007
ROD: UHVNA_VW36.rod
VCID: 32601048D447
No fault code found.
Sorry if this needs to go past you Maverick, please delete or amend has you see fit,
This is the coding for the new 3C8 035 730A unit,
Byte 0 Language:
00?
01 German
02 English
03 French
04 Italians
05 Spanish
06 Portuguese
08 Czech
07-09-FF not allowed
Byte 1. Voice Command:
00 activated
01 disabled
Byte 2.Type Microphone:
Parameter 00 1 / microphone VW
01 parameters 2 / microphone VW
10 parameters 1 / microphone Audi
02-03, 11-13 parameter set 3-4 / VW and Audi
Byte 3. Diagnosis antenna:
00 active
01 inactive
Byte 4. Diagnosis fixing Laptop (Überwachung Baseplate):
00 active
01 inactive
Byte 5. Mute (cooperating):
00 active
01 inactive
Byte 6. Control unit for the mobile phone preparation (module three keys):
00 Module 3-button activates / SMS possible
01 Module 3-button inactive / SMS possible
10 3-button activates / SMS is not possible
11-button inactive / SMS is not possible
Byte 7. Multimedia function:
00 BT Audio Active / Active Multimedia Context
01 BT inactive Audio / Multimedia Assets Background
10 BT Audio disabled Active / Inactive Multimedia Context
11 BT inactive Audio / Multimedia Background Off
Byte 8. Type of registration of mobile phone:
00 Supporting THB
01 Support VDA
10 Support Paragon
Byte 9. Function call for help:
00 people with disabilities
01 activated
Byte 10. Fuel Type:
00 Unknown
01 Gasoline
04 Diesel
05 LPG
06 natural gas
08 Electricity
10 hydrogen
Byte 11. Vehicle type:
00 M1
01-05 M2 and N1-3-3
Hope this helps any one interested
Thanks, I’ve created a page with this info and will expand my bluetooth information to include this unit.
Volkswagen 9WZ Bluetooth Programming
Hello,
I have installed 1Z0035729B bluetooth in my 2006 mk5 R32 with RNS510. I did all coding and adaptions and it works good with no fault codes at all.
But my problem is when i scan bluetooth devices on my iphone 4 or any other phones it shows Skoda_UHV. How can i change that to VW_UHV?
PLease help
Thank you very much
Hi i have a mk edition 30 iv put a bury nokia 6700 cradle and programmed in on the vcds system but it showing live shorted out on supply to cradle (factory fitted system with the nokia bluetooth unit under driver seat)
Hi, could do with some urgent help.
Just taking delivery of a 2011 Tiguan with RCD510. Bought the bluetooth 3C8035730A from internet supplier. My dealer has fitted it but claim they can not get the car to recognise it.
Does the unit itself need some coding and what can I do to give them guidance on vehicle coding.
Thanks in anticipation
Hello all…
I have a late 2003 Touareg with the RNS2 NAV system and Color MFD.
I bought and installed the 3C0 035 729 F Bluetooth module.
I also have the aftermarket vag-com ODB-II cable running the 805.1 vag-com version.
The problem is that I can’t access the Telephone module (77). VCDS won’t find it.
I did some research and it seems that I have to enable it via CAN GATEWAY.
I know that my module works because once I unplug it, i get an error on CAN GATEWAY module. When I plug it back in, and clear the error, I don’t get an error again. When I turn on the RNS2 the screen shows momentarily “Phone Active” or something like “Phone is Activated”
BUT….The vag-com only gives me the soft code 000006 for CAN Bus because my Touareg has CAN BUS 1.6.
I don’t get any long coding option to choose bit 7 (telephone).
My Questions are:
-Can I edit the 000006 to something else in order to enable the bluetooth module?
-Is there a way to enable it otherwise with my cable and software?
-What If I plug it into a new SKODA Superb, code it, and then plug it back to my Touareg?
Guys PLEASE help me out here….Its been 6 months that I trying to make this to work…
Any progress?
I have the same problem!
Hi guys, about to attempt to install a 9W7 VW Bluetooth unit (part number 7P6 035 730 C) into my wifes new 2011 Polo 6R (with the RCD-510 headunit).
Trouble is, on my new Scirocco )wih the same bluetooth module), I had to do the pairing via the Highline display. My wifes polo only has a midline display, so obviously won’t display a Phone menu. Not a problem once it’s paired, as all call details etc. should come up on the RCD-510, trouble is how do I pair her phone with it without Highine ?
I have a HEX-CAN genine Ross Tech cable, and am hoping there’s an adaptation channel somewhere that will invoke the visibility and pairing of the phone. Anyone know if this is possible please ?
I just installed a Skoda UHV unit (929B) in my 2007 VW GLI. I have the RNS-510 and MDI interface, multifunction steering wheel, and Full MFA display.
I coded controller 77 (Telephone) to 0000422, as 0000477 would not take. It gave me an error that it was out of range, even though the VAG-COM showed US English should be 7 and UK English is 2. It works, but I’m wondering why it won’t take US English.
Also, I’m a little confused on digits 3 and 4 from the left:
0x?xxx: Steering Wheel Type
0 – non multifunction steering wheel
1 – standard steering wheel
2 – modular steering wheel
0xx?xx: Installed Components
1 – none
2 – Multi Function Steering Wheel
3 – Head Unit
4 – Multi Function Steering Wheel and Head Unit
5 – K-line
6 – Multi Function Steering Wheel and K-line
7 – Head Unit and K-line
8 – Multi Function Steering Wheel, Head Unit and K-line
At the very top, Maverick says to code as 0000422 as I did, but in his setting but digit 3 is set to 0, which is non multifunction steering wheel, and then digit 4 is Multi Function Steering Wheel and Head Unit. Can someone make any sense of this for me?
I’m also curious about is what John was asking about in December about renaming the Bluetooth SSID. Is there a way to do that through the Adaptation process? I know you can change the PIN to something less obvious than 1234 (already done), but Skoda defiantly doesn’t apply to my car.
One last issue, it seems to take forever to download the phone book from my phone. It really won’t let me do anything with the phone for 5-10 minutes after I get in the car. Is there a way to only download updated phone entries, or is this what I can expect in the future.
Hi guys, I just installed a 5no 035 730a into my red dot 2009 scirocco with RNS510. It works fine but I can’t get the push to talk button toonly work with the RNS510 voice control. If I program it to use only rns then muting does not work. If I program it to use the Bluetooth module voice control then all is fine, but I want to use the RNS voice controls instead. I suspect the coding is wrong, as it says incorrectly coded when I make it use RNS voice control. But at the moment there is no error, but it sucks using the Bluetooth module voice dialing. Any advice?
Ps the wiring is correct for micrpone, its just a coding issue.
I have a factory VW installed, RCD-510 (5K0 035 190) + Bluetooth (7P6 035 730B). My question is as follows. With the3 factory installed system in my 2011 GTI. Can I simply recode to allow voice dailing? or do I require new parts or a bluetooth upgrade?
Thanks
Hi All, I have a new VW GOLF – Match edition. The bluetooth was working fine for a week but now the bluetooth seems to have deactivated itself somehow. Can’t see the phone option on the front panel behind the steering wheel and also when I flick through the arrows on the multifunction steering wheel the phone option is missing… I am taking the car back to them to have a look but thought of asking experts over here if they can help me
Thanks
Simon
hi all, ive been reading this post with interest… could i please ask, do i need special equipment ( computer/vagvas-not sure what this is?) if i want to instal a guenuine vw bluetooth kit into my 2010 tiguan? i read all about codes etc but not sure if this is done with an interface or just via the radio controls . sorry if this is a silly question but i would appreciate any advice. thanks, mike in australia
hello
your post are great!
i used them for installing the rear camera
i have a few tips rigarding the wiring if you want
i just bought the Bluetooth VW RNS 510 9W7 UHV AD2P / 5K0 035 730 D,E,F!!! 2012!!! newer than 7P6!
do you have any special indications? i will install it in my new golf r 2011 with th erns 510
thank again for your help
albert
israel
[...] GA_googleFillSlot("WATERCOOLED_BTF_MREC"); Scroll down to see the adaption settings: Volkswagen / Skoda Bluetooth Programming | my-gti.com Shark Blue VW Golf MY10 118TSI DSG w/ beige leather interior. Retrofitted: RNS510, 9W3 [...]
HI,
Had upgraded my rSAP bluetooth module from 5N0 035 730B to 3C8035730B so that I can get HFP and AD2P. The change was a success but i realised the following:-
My existing columbus had voice command where i can switch from radio to map to navigation, etc which can be activated by the top right button on the HU and also via the left steering wheel scroller.
After the Phone module upgrade, the wheel scroller on steering only do voice command on the phone function but not the rest. Voice command via the top right button on columbus still work. Was wondering if anyone encounter this and had the solution. thanks
Hi I have 2009 Superb 1.8 TSI AT. I like to add Blue tooth Kit to my car. I like to know Do I need any information from dealer ? Do I need any speciel tools? What Module I need and where I can buy? important question is ” If I mess up programming during instalation then Wil be able to use the car or It will stall.” thanks in advance