«  
  »

Volkswagen RNS 510 Firmware Upgrade to version 2700 / 2702 / 2704 / 2706 / 2708

Version 2700 / 2702/ 2704 / 2706 / 2708 Firmware for the Volkswagen RNS 510 and the Skoda Columbus has been released. So far it appears to be only bug fixes and the 2660′s new features remain

  • Voice Control (requires microphone – see Volkswagen RNS 510 Microphone Connection for voice control)
  • Speed Limit Display
  • Stability Improvements
  • Faster Startup (this has been improved on 2770)
  • Display OPS and RVC at the same time
  • SDHC 32 GB Support (HW04 and above)
  • Display Off on extras tab
  • Climatronic control if approriate climatronic fitted
  • Clock display if RNS 510 swtiched off (buggy)
  • Excluded roads (under route options)
  • GPS coordinates entry
  • Additional adjustments for video
  • Larger RVC screen with transparent menus at the side

Further details on the features can be found on the following page: Volkswagen RNS 510 Firmware version 2660 / 2662 / 2664 / 2666 / 2668 new features

Units that can be upgraded include (still being compiled may not be 100%)

  • 1T0 035 680 C (1T0035680 C) from software version 1000, 800,  900, 1100 and 2660 to version 2700.
  • 7L6 035 680 C (7L6035680C) from software version 1002,  1022, 1102 and 2664 to version 2700.
  • 3T0 035 680 A (3T0035680A) to version 2704.
  • 7F0 035 680 (7F0035680) to version 2700.
  • 7E0 035 680 (7E0035680) to version 2700.
  • Further to follow as the firmware is loaded.
  • USA Firmware has yet to be released

Download the files and extract them using winrar and you will have a NRG format ISO file to burn. Using Nero burn a DVD+RW or DVD-R (CDR works as well) at a slow speed (4 x is ok for DVD and 16 x for CD). Make sure you use quality media and keep the burn speed down as low as you can to ensure there are no problems during the installation process. Also note that you may need to edit a file before you burn it (see below) if you want to access the setup menu without Vagcom/VCDS.

Warning! This upgrade WILL delete your music and/or maps if you have a firmware version PRIOR to version 1100/1102. Units with a firmware version of 1100/1102 will not have music and maps deleted.

Warning! There is a remote chance of you ‘bricking’ the unit, this is a fraction of a percent but it could happen! The process takes around 60 minutes.’

Warning! There are a small number of users where the RNS 510 does not know where it is after it’s been powered on, details of the previous location are kept in the unit but at this stage there is no pattern to this problem.

Warning! Users with cars MY07 and earlier may experience power drain issues after the upgrade. See the post “Upgrading 2nd generation radios (RCD 300, RCD 500) to 3rd generation (RCD 210, RCD 310, RNS 310, RCD 510) power drain issue” for more details.

Warning! Users with the Skoda UHV bluetooth 1Z0 035 729 B (1Z0035729B) may want to delay upgrading the firmware, there is an issue with the RNS 510 no longer displaying the phone book and/or the call details but signal strength etc are visible for some phones. My HTC Diamond for example worked fine before the update but only partially afterwards however my Iphone 3G worked fine before and after. This is not a problem with the 1Z0 035 729 D (1Z0035729D) Skoda UHV bluetooth kit. The MFD functions as per normal with phone book and last calls listed correctly. Android 2.1 phones work fine with the update.

Note! - Test/Setup Mode. The firmware can allow access to enter test/setup mode without Vagcom/VCDS access see Accessing the Setup Menu on the RNS 510 head units with firmware later than 1100. The procedure for entering the test/setup mode for those with Vagcom/VCDS is slightly different as well. To enter the test/setup mode when the RNS 510 is operating press and hold the setup button, keep holding it when the radio menu appears and shortly after the test menu appears . I had to reboot my unit after coding it but it may be possible a power cycle is enough.

Note! - Failure (Gateway Error 202) - You can downgrade back to 1100 by inserting the 1100 firmware and rebooting the RNS 510 (Setup + eject + info).

Steps to load firmware

  1. Unlock and/or open the car
  2. Do not start the car
  3. Turn the RNS 510 on and insert the firmware CD/DVD into the drive

Download Firmware Upgrade

Preferred Download Location (Thanks Speed)

Backup Download Location (Thanks Artek)

File Password: halkon77wie$ch88
File 1: http://rapidshare.com/files/358746579/4.801.340-t450-c6.part1.rar
File 2: http://rapidshare.com/files/358756430/4.801.340-t450-c6.part2.rar
File 3: http://rapidshare.com/files/358762379/4.801.340-t450-c6.part3.rar
File 4: http://rapidshare.com/files/358768820/4.801.340-t450-c6.part4.rar

Version Information from VERSION.TXT

--------------------------------------------
Software Loading CD for CP2 based units
(c) CONTINENTAL Wetzlar

CdTreeBuilder version 3.06 is used.
--------------------------------------------

#CD:P 0 0 4 . 8 4 0 . 3 0 1


#CD:P 0 0 4 . 8 4 0 . 3 0 1
#DATE:2009-11-19

#Project: VWRNS
#Author: RoNe
#Steckbrief: C_EU_9.242_t450 C6

#CommentStart:
This is a SWL CD for VW delivery.

#CommentEnd:

#Integrationphase: Delivery cw45/09 C6-samples
#VwSwPartNumber:1T0035680C/1T0035680C/7L6035680C/3T0035680A/7F0035680/7E0035680
#VwSwIndex:2700/2706/2702/2708/2704
#AppsBuild:C_EU_9.242_t450 C6
#CRC16:dc42

Firmware loading steps from start to finish (2660 but the process is the same)

March 8th, 2010 | Tags: , , , , , , | Category: Firmware Updates, In Car Entertainment, RNS 510, Reference

51 comments to Volkswagen RNS 510 Firmware Upgrade to version 2700 / 2702 / 2704 / 2706 / 2708

Leave a Reply

 

 

 

You can use these HTML tags

<a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>